Wood & steel frame
Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Parts & Welding for Spring Valley Homeowners
A gate that drags, sags, or won’t latch is usually a parts problem, not a replacement problem. At Gatewood Fence & Gate, we weld, brace, and re-hang gates on site in Spring Valley instead of hauling them off, and we quote the price before we touch a thing. Our technicians have up to 25 years of experience, we service nine major gate brands, and every job is stamped with our 90-Day Done Right Promise in writing. When your gate needs a new hinge, a welded rail, or a latch that actually catches, call (888) 300-3906 and a live person picks up, day or night.

What Our Gate Parts & Welding Service Includes
Most gate trouble shows up in the same handful of places: the hinge post, the rails, the rollers, the latch. Here’s what we actually do about each one, and when it makes sense to call.
Hinge Replacement
Hinges carry the whole weight of a swinging gate, and when they wear out the gate drops, drags on the ground, and pulls the post out of plumb. We replace worn hinges with correct-weight hardware, re-set the gate to swing true, and reinforce the mounting points with new welds so the repair holds. If one hinge is shot, we check the rest, because a gate riding on two tired hinges is a gate that’s about to sag again.

Post Replacement
When a hinge post rots at the base or wobbles in the ground, no amount of hinge work will fix the swing. We set a new post, tie it into the existing fence line where we can, and weld the gate back onto a solid anchor. A gate sags in the hinge post, not in the middle, so this is where we start when the whole gate is leaning.

Rail Repair
Rails crack at the welds, bow under weight, or rust through at the bottom where water sits. We cut out the bad section, weld in new rail, and repaint the repair so it blends with the rest of the gate. Fix the rail without checking the post underneath and you’ll fix it twice, so we look at both before we quote.

Custom Welding
Sometimes a gate needs a brace, a gusset, a new latch plate, or a custom bracket that no catalog sells. We weld on site in Spring Valley, which means your gate stays in your driveway and your fence line stays intact. This is also how we rescue older gates that a replacement outfit would rather tear out and sell you new.
Gate Rollers
Sliding gates ride on rollers, and when those seize up the whole gate shudders, jumps the track, or stalls the opener. We replace worn rollers, true up the track, and check that the gate is running level so the motor isn’t fighting the hardware. If the opener has been straining, it’s worth having the rollers looked at before the motor gives out.
Latch & Lock
A latch that won’t catch is a security problem, a convenience problem, and often a sign the gate has shifted out of alignment. We repair and replace latches, self-closing hardware, and lock assemblies, and we align the gate so the latch meets its strike cleanly. Call us about a gate repair visit and we’ll look at the whole mechanism, not just the latch.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Brands We Service for Gate Parts & Welding
We’re certified to service nine major gate brands, and after this many years we know exactly where each one wears out. BFT operators tend to be solid, but their mounting hardware takes a beating on heavy gates, so we check the brackets and welds whenever we’re called out on one. Linear and Viking systems are common on residential sliding gates around here, and we know their roller and track setups well enough to tell you whether the gate or the operator is the real problem.
Ghost Controls is another brand we see a lot on driveway gates, and we handle the hardware side of those installs, from hinge alignment to latch geometry. Whether you have BFT, Linear, Viking, Ghost Controls, or any other make, we can help. And if the trouble turns out to be the motor rather than the gate itself, we’ll tell you straight and point you to our gate parts and welding service for the hardware side of things.
Signs You Need Gate Parts & Welding Right Now
- The gate drags or scrapes the ground. That’s usually a worn hinge or a post that has shifted, and left alone it will chew up the gate frame and strain the opener. A dragging gate is a slow-motion repair bill, so it’s cheaper to catch it early.
- The gate won’t latch or lock. A latch that misses its strike means the gate has moved out of alignment, and a gate that won’t secure is one you can’t trust at night. We realign and repair the latch so it catches the way it should.
- Visible cracks or rust at the welds. Rust at a joint weakens the weld from the inside out, and a cracked weld on a rail or hinge point is a failure waiting to happen. We cut out the bad section and weld it fresh.
- The hinge post wobbles when you push on it. A loose post means the gate has nothing solid to hang from, and pushing it back and forth makes it worse. That’s a post replacement, and it’s the first thing we check.
- The gate shudders or jumps on the track. Seized rollers or a bent track will stall a sliding gate and overwork the motor. We replace the rollers and true up the track so the gate runs smooth again.
Our Gate Parts & Welding Process – Step by Step
- 1
We answer the phone and ask what it’s doing. A live person takes your call, not a voicemail or a dispatch queue, and we ask enough questions to know whether it’s a hinge, a post, a roller, or the operator. That saves a trip and gets you a better first answer.
- 2
We come look at the gate in person. Nobody can quote a weld over the phone, so we inspect the gate, check the post for movement with a level, and test the hardware by hand. We look at the whole gate, not just the part that’s making noise.
- 3
We give you a written price before any work starts. You get a clear number for the parts and the labor, agreed before we pick up a tool. No surprises at the door, and no “while we’re in there” additions you didn’t approve.
- 4
We weld and repair on site. Our technicians set up in your driveway, cut out the bad metal, weld it back solid, and re-hang or re-align the gate. Your gate never leaves your property, and you can watch the whole job if you want to.
- 5
We walk the gate with you and stamp the promise. We open and close it together so you can see it working, and every job carries the 90-Day Done Right Promise in writing. If something isn’t right within that window, one call brings us back.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Parts & Welding Cost in Spring Valley?
Most gate parts and welding jobs in Spring Valley come in between a couple hundred and a few hundred dollars, depending on what’s actually wrong. A hinge replacement on a standard swing gate typically runs $150 to $300, a rail or weld repair $200 to $450, roller replacement on a sliding gate $125 to $300, and a hinge post replacement $350 to $800 when the old post has to come out and a new one set. Latch and lock work usually lands at $100 to $250.

What moves the price is the weight of the gate, whether it’s steel or aluminum, how much of the frame needs cutting out, and whether the post set is straightforward or the ground fights back. We don’t pad the quote, and we don’t sell you a new gate when a weld will do. If you’ve got a written estimate from someone else, bring it to us for a free second opinion and we’ll tell you honestly whether it’s fair.
Every estimate is free, there’s no trip charge inside the county, and we’ve got standing offers that don’t require haggling: $40 off any repair over $200 and a permanent 10% discount for seniors and veterans. The price is quoted and agreed before any work starts, so the number you hear is the number you pay. Call (888) 300-3906 for an exact quote.
Gate Parts & Welding Near Spring Valley – Our Service Area
We handle gate parts and welding across Spring Valley and the neighboring communities: Summerlin, Enterprise, Paradise, Winchester, Las Vegas, Whitney, Sunrise Manor, Henderson, North Las Vegas, Boulder City, and out toward Sandy Valley. If you’re in Summerlin or Enterprise, we also cover gate parts and welding in Summerlin and gate parts and welding in Enterprise with the same on-site welding approach. We’re close by, so most jobs in Spring Valley get looked at quickly, and an emergency call gets a live person on the phone right away.
Serving Spring Valley, NV – Our Local Coverage Area
We serve Spring Valley and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Gate Parts & Welding in Spring Valley
It’s repair work on the physical gate itself rather than the motor: hinges, posts, rails, rollers, latches, and any custom welding a gate needs to function. Instead of replacing the whole gate, we fix the specific part that failed, often welding it right in your driveway. The goal is to get your gate swinging or sliding true again without paying for a full replacement.
Most hinge, roller, latch, and rail repairs are done in a single visit, usually a couple of hours on site. Post replacements and heavier weld jobs can run longer, but we give you a realistic window when we quote. We don’t rush a weld to save time, and we tell you upfront if a job needs a return visit for a part we have to order.
Hinge replacement typically runs $150 to $300, roller replacement $125 to $300, and latch or lock work $100 to $250, with post replacement and heavier welding higher depending on the gate. The exact number depends on gate weight, material, and how much needs cutting out. We quote and agree the price before work starts, so there’s no surprise invoice. Call (888) 300-3906 for an exact quote, and estimates are free.
Yes, we’re certified to service nine major brands, including BFT, Linear, Viking, and Ghost Controls. We know where each brand’s hardware tends to wear out, whether that’s the mounting brackets on a BFT operator or the roller setup on a Linear sliding gate. If the issue turns out to be the operator rather than the gate, we’ll tell you and point you toward our gate parts and welding service for the hardware repairs.
Yes, a live person answers our phone 24 hours a day, 7 days a week, so an emergency call gets a real answer, not a voicemail. A gate that won’t secure or has come off its track is a priority, and we’ll tell you on the phone what we can do and when. We won’t promise a dispatch window we can’t keep.
Every job carries the 90-Day Done Right Promise in writing. If something we repaired isn’t right within that window, one call brings us back to make it right, with no runaround. It’s stamped on the job, not buried in fine print, and the name on the invoice is the name on the shop.
Clear the area around the gate so we have room to work, and if you can, have the gate in the position where the problem shows up so we can see it. For a motorized gate, tell us the brand and whether the opener is throwing an error, since that helps us diagnose faster. If you have a written estimate from another company, have it handy for your free second opinion.
Schedule Your Gate Parts & Welding Service in Spring Valley Today
Don’t replace a gate that just needs a hinge, a weld, or a new roller. Call Gatewood Fence & Gate at (888) 300-3906 and get a free, no-obligation estimate on gate parts and welding in Spring Valley, quoted and agreed before any work starts. A live person answers around the clock, and every job is backed by our 90-Day Done Right Promise in writing. If you need the motor side handled too, our related gate service page covers it.
Written by the team at Gatewood Fence & Gate.