Wood & steel frame
Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Repair for Spring Valley Homeowners
Most gate failures we get called out for in Spring Valley start the same way: the gate closes on its own, then drags, then stops halfway and hums. That is usually a hinge post that has given up in caliche soil, not a motor problem, and it is exactly what we fix. Our technicians have up to 25 years of experience, and every repair carries the 90-Day Done Right Promise in writing. Same-day repair is often available in Spring Valley, and a live person answers when you call (888) 300-3906.

What Our Gate Repair Service Includes
Electric Gate Repair
Electric gates fail in three familiar places: the control board, the safety loop buried in the driveway, and the transformer feeding the operator. When you call, we test the circuit before we touch a single part, because a gate that “won’t open” is often a tripped breaker or a loop that got cut during a driveway pour. In Spring Valley, our summer heat cooks control boards and ages low-voltage wiring faster than most homeowners expect. We repair the board when it can be repaired, re-run the loop when it has failed, and test the whole circuit in front of you before we call the job done.
Automatic Gate Repair
An automatic gate that reverses at random, stops mid-travel, or ignores the remote is a real safety concern, not a minor annoyance. Cause number one is a limit switch that has drifted, followed by a worn drive gear and a remote that lost its pairing after a power surge. We service LiftMaster, Linear, Viking, and Ghost Controls operators, read the fault codes on the control board, and rebuild the operator rather than swapping it out when a rebuild solves the problem. You’ll get an upfront price before any work starts.
Hinge & Post Repair
A gate sags at the hinge post, not in the middle. Fix the panel without the post and you’ll fix it twice. Spring Valley sits on expansive clay and caliche that shifts with the wet winters and dry summers, so posts pull, lean, and settle in ways homeowners elsewhere rarely see. We check post plumb with a digital level, reset a leaning post in fresh concrete when it will hold, and weld a bent hinge back to true when the metal is sound. If the post is beyond saving, we tell you straight instead of patching it and charging for a return trip.
Gate Realignment
A gate that drags the ground, won’t latch, or scrapes the post has shifted out of alignment, and it is usually the frame and hinges, not the latch. Left alone, realignment turns into a bent frame, a cracked weld, and a much bigger repair bill. We square the frame, adjust the hinges, and check the gate against the strike plate so it closes clean and latches on the first push. Gates that pass a visual check can still be out of square by an inch, which is why we measure rather than eyeball.
Lock Repair
A gate lock that sticks, spins free, or refuses the key is a security gap, and it rarely fixes itself. Gate locks fail from dust, heat, and worn tumblers, and the fix is often a clean, a re-key, or a new latch assembly rather than a gate replacement. We repair keyed locks, thumb latches, and magnetic locks, and we check the strike alignment so the lock catches the way it should. If your lock is paired with an access keypad or intercom, we test that it all works together before we leave.
Weld & Rust Repair
Broken welds and rust-through are the two failures that end a gate’s life too early when they go unaddressed. Spring Valley’s monsoon rain and dry heat work on steel in different ways than coastal climates do: not constant salt, but cycles of flash flooding and baking sun that fatigue welds and blister paint. We bring the welding rig to your driveway, weld the frame and hinge back to full strength on site, grind it smooth, and treat the rust so the repair holds. On-site welding is the whole point: the gate stays where it lives, and the repair happens under real load instead of on a shop floor.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Brands We Service for Gate Repair
We are certified to service nine major gate brands, and we know where each one wears out because we have repaired them across the Las Vegas valley for years. BFT operators are rugged but their control boards fail from heat and voltage spikes, and we have seen our share of them here. Linear swing and slide operators are common on residential driveways and develop gear wear and limit-switch drift after years of use. Viking operators are built to hold up, but their battery backups and receivers need attention when a homeowner can’t remember the last service.
We also service LiftMaster, FAAC, DoorKing, Elite, Mighty Mule, and Ghost Controls. Whichever make you have, we read the manufacturer’s fault codes rather than guess, and we tell you whether a repair actually holds or whether replacement is the honest answer. Whether you have a BFT operator or any other make, we can help.
Signs You Need Gate Repair Right Now
Some symptoms are safe to watch for a week. Others are a safety problem today. Here is how to tell them apart.
- The gate closes on its own or reverses at random. A drifting limit switch or a failing safety sensor can send a gate into a car, a child, or a pet. Stop using the operator and call us. A gate that moves without command is a hazard, not an inconvenience.
- The gate sags, drags, or won’t latch. A sagging gate puts load on the operator that it was never built for, and every cycle wears the motor and gear faster. Fix the hinge and post before the operator pays the price.
- The lock or latch sticks or spins. A gate that won’t lock is a security gap. Small lock repairs today cost less than a bent gate frame tomorrow.
- You see rust, a cracked weld, or a bent frame. Rust through a hinge tube or a cracked weld at the post is structural, and it gets worse with every open and close. Spring Valley’s monsoon cycles push water into failing paint and finish the job.
- The operator hums but doesn’t move, or trips the breaker. That is electrical, and it should be treated that way. Turn the power off at the breaker and call us. Gate operators run on line voltage and should be diagnosed by a trained technician, not by trial and error.
Our Gate Repair Process – Step by Step
- 1
Call and describe what you see. A live person answers around the clock, so you talk to someone who can ask the right questions instead of leaving a message. We note the operator brand, the symptom, and how long it has been happening. That saves time on the visit.
- 2
Free estimate on site. We look at the gate, the post, the hinges, the operator, and the wiring, then tell you what is wrong in plain language. Prices are quoted and agreed before any work starts. You’ll also get a free second opinion on any written estimate you already have from another company, so you can compare.
- 3
Diagnose before we repair. We use a digital level on the post, a multimeter on the operator circuit, and the manufacturer’s fault codes on the control board. We don’t replace a part that tests good, and we don’t guess at the problem so we can bill for a call-back.
- 4
Repair on site, with welding when the gate needs it. The gate stays in your driveway. We weld broken hinges and frames on location, realign the gate, repair the operator, and fix the lock. You watch the work happen, and you can ask questions as we go.
- 5
Test it and back it in writing. We cycle the gate, check the safety sensors and the latch, and walk through what we did. The 90-Day Done Right Promise is on the invoice, and one call brings us back if something isn’t right.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Repair Cost in Spring Valley?
Most gate repairs in Spring Valley run in a predictable range. A typical hinge or post repair runs $150 to $400 depending on whether the post has to be reset in concrete. Gate realignment and lock repair usually come in between $95 and $250. An electric or automatic gate repair, such as a control board swap, a safety loop re-run, or an operator gear rebuild, runs $200 to $650 depending on the brand and whether the parts are in stock. On-site weld and rust repair runs $175 to $500 depending on how much metal needs to be cut out and rebuilt. These are ranges, not quotes: your estimate is written and agreed before we start.

What moves the price: the operator brand, how long the gate has been failing, whether a post has to be reset, and whether the wiring has to be traced. You avoid overpaying by fixing the post and hinge before the operator takes the strain, and by getting a written estimate you can hold a company to. Seniors and veterans get a permanent 10% discount, and any repair over $200 gets $40 off, no haggling required. There is no trip charge inside the county.
Gate Repair Near Spring Valley – Our Service Area
We repair gates across Spring Valley and the surrounding valley, including Summerlin, Enterprise, Paradise, Winchester, Las Vegas, Whitney, and Sunrise Manor. We also work out to Henderson, North Las Vegas, Boulder City, and Sandy Valley. Typical response times run roughly 30 to 60 minutes across Spring Valley and closer neighborhoods, and outlying towns extend that window. You can get gate repair in Spring Valley handled on site the same day in most cases. If you’re in Summerlin, gate repair in Summerlin is a call away, and Enterprise is a quick trip too: gate repair in Enterprise. We also cover gate repair and fence work across the valley.
Serving Spring Valley, NV – Our Local Coverage Area
We serve Spring Valley and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Gate Repair in Spring Valley
Gate repair is fixing the specific part that has failed on your gate: the operator, hinges, post, frame, lock, wiring, or weld. It is different from gate replacement, which means a whole new gate and hardware. We repair the part that failed rather than sell you a new gate, and we tell you honestly when a repair is no longer worth it.
Most repairs finish in one visit of one to three hours, and simple jobs such as a lock repair or a realignment can wrap in under an hour. Repairs that need a specific part ordered for your operator brand may take a day or two while the part comes in. We tell you the expected time before we start, and we don’t leave a gate half-repaired.
Most repairs run between $95 and $650 depending on the part and the brand. Hinge and post repairs, realignment, and lock work tend to sit in the lower half of that range, while operator and control-board repairs sit higher. We quote and agree the price before any work starts, and a free second opinion on any written estimate is always available. Call (888) 300-3906 for an exact quote. Estimates are free.
We are certified to service nine major gate brands, including LiftMaster, Linear, Viking, Ghost Controls, BFT, FAAC, DoorKing, Elite, and Mighty Mule. Tell us the make and model when you call and we’ll confirm what is likely failing. On most brands we can read the manufacturer’s own fault codes to find the problem fast.
Yes, and a live person answers around the clock. A gate that is stuck open in a driveway, reversing at random, or blocking a car is a safety problem, and we treat it that way. Call (888) 300-3906, and we’ll arrange the soonest visit. If the gate is a hazard to people or vehicles, stop using the operator and turn the power off at the breaker until we arrive.
Every repair carries the 90-Day Done Right Promise in writing. If the repair isn’t right, we come back and make it right, and one call brings us out. The promise is stated plainly on the invoice with no hedge language and no runaround.
Clear the area around the gate and post and note when the problem started and whether it’s getting worse. If you have the operator manual or a prior estimate, set it out so we can review it. Turn the operator off at the breaker if the gate is moving on its own, and make sure someone is home to walk through the gate with us.
Schedule Your Gate Repair Service in Spring Valley Today
A sagging gate, a stuck lock, or an operator that won’t respond is fixable, and usually fast. Call (888) 300-3906 and a live person answers, around the clock. You’ll get an upfront estimate, no trip charge inside the county, and the 90-Day Done Right Promise in writing. One call, and we’ll get your gate working again.
Written by the team at Gatewood Fence & Gate.