Wood & steel frame
Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterDriveway Gate in Spring Valley, NV
A driveway gate in Spring Valley, NV typically costs between $2,400 and $7,500 installed, depending on width, material, and whether you add an opener. If your current gate is sagging, dragging, or stuck open, repair usually runs $180 to $650 and is the smarter call than replacement. We’re Gatewood Fence & Gate Spring Valley, and driveway gates are a big part of what we do here: swing gates, slide gates, wrought iron, chain link, and the openers and access control that run them. Call (888) 300-3906 and a live person picks up, day or night.
What separates a driveway gate that works for fifteen years from one that quits in two is rarely the gate itself. It’s the hinge post, the footing, and the operator. We start at the post and work outward because that’s where the failure almost always lives. If you’re weighing a full replacement against a repair, start with our Gate Installation page for the broader picture, or keep reading for the driveway-specific detail.
Some things about Spring Valley matter here. The ground out toward the foothills and the older lots near the golf courses can be caliche-heavy and stubborn, which changes how a post gets set and how deep we go. The summer sun bakes anything metal and expands steel enough that a gate that closed flush in April can bind by July. Wind through the valley pushes on a wide swing gate harder than people expect. We build and adjust around all of it because we live here too.
When You Need Driveway Gate Service
Most calls we get aren’t a mystery. The gate tells you something’s wrong long before it stops moving. Here’s what we hear most in Spring Valley.
- The gate sags and drags on the ground. A gate sags in the hinge post, not in the middle. When the bottom corner catches the concrete or pavers, the post has shifted or the hinge has worn, and adjusting the gate without fixing the post just buys you a few weeks.
- The opener runs but the gate doesn’t move. Could be a stripped gear, a dead battery in the remote, or a safety sensor knocked out of alignment by the sprinkler guy. On Linear and Viking operators this is often a quick diagnosis.
- The gate swings open on its own or won’t latch. Show us the gate closing on its own and we’ll show you where it’s failing. This is almost always a plumb and level problem, sometimes a hinge-post footing that’s settled.
- You want a gate where there wasn’t one. New driveway gate for privacy, for keeping the dogs in, or for controlling who pulls up to the house. We size it to your opening and your vehicles, not to a catalog page.
- The old gate is rusted through or bent from a hit. On a welded steel or wrought iron gate, on-site welding often saves the gate instead of replacing it. We weld in your driveway rather than hauling it off.
- You need keypad or remote access added. New opener, new keypad, or a fob for the family and the cleaning crew. We work with DoorKing and LiftMaster access gear alongside BFT and Ghost Controls operators.
Our Driveway Gate Process
Here’s what happens from the first call to the final walk-through. No surprises, no mystery line items.
- You call and talk to a person. Not a voicemail, not a queue three states away. We ask what the gate is doing, how wide the opening is, and whether there’s an existing operator. That tells us what to bring.
- We come out and look. We check the hinge posts, the footings, the gate’s swing or slide track, and the operator if there is one. We measure the opening and note the grade and the ground. A free second opinion on any written estimate you already have is yours for the asking.
- You get a price in writing before we touch anything. Upfront pricing means the number we quote is the number you pay. No trip charge inside the county. If it’s a repair over $200, take $40 off. Seniors and veterans get a permanent 10% discount.
- We do the work on site. Most repairs happen in your driveway the same visit, including welding. Installations get scheduled and set on proper footings. Fix the panel without the post and you’ll fix it twice, so the post comes first every time.
- We test it with you watching. Gate opens, closes, latches, the safety sensors trip and recover, the keypad works. You operate it before we pack up.
- It’s covered in writing. Every job carries the 90-Day Done Right Promise. If something isn’t right, one call brings us back. No runaround, no fine print.
Driveway Gate Pricing in Spring Valley
Here’s an honest breakdown of what driveway gate work runs in Spring Valley. These are real ranges, not teaser numbers that change at the door. Your exact price depends on width, material, footing conditions, and whether an operator is involved, and we’ll put it in writing after we’ve seen the gate.
| Service | Typical Cost Range |
|---|---|
| Gate repair (sag, drag, hinge, latch) | $180 – $650 |
| On-site welding repair (steel or wrought iron) | $200 – $500 |
| New swing gate, installed (single, up to 14 ft) | $2,400 – $5,200 |
| New slide gate, installed | $3,500 – $7,500 |
| Gate opener / operator installed | $650 – $1,800 |
| Keypad or access control added | $250 – $700 |
What moves the number: gate width and weight, material (chain link is the least expensive, wrought iron and steel run higher), how deep the footings have to go in caliche, and whether the operator is a straightforward swing unit or a slide operator that needs a track and safety edges. A post replacement adds cost but skipping it is false economy.
Standing offers that don’t require haggling: $40 off any repair over $200, no trip charge inside the county, a free second opinion on any written estimate, and a permanent 10% discount for seniors and veterans. That’s it, and it’s the same for everyone. Call (888) 300-3906 for a free estimate.
Repair or replace?
Is it cheaper to repair or replace a driveway gate? Repair is almost always cheaper when the posts and frame are sound, often a fraction of replacement. Replace when the frame is rusted through, the post footing has failed beyond resetting, or the gate has been hit hard enough to twist the whole structure. Our default is repair first, because a gate that’s fixable shouldn’t become a sales call.
How long does a driveway gate installation take?
A single swing gate installed on new footings usually takes one to two days, with concrete cure time adding a few days before the gate is loaded. Slide gates and gates with operators can run two to three days. We’ll give you a realistic window, not an optimistic one.
Do you install gate openers?
Yes. We install and service openers from LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, and we’ll match the operator to your gate’s weight and how often it cycles. A heavy gate on an undersized operator is a common cause of early failure.
Can you come out today?
Often, yes, especially for a gate stuck open or one that won’t latch, since that’s a security matter. We answer live around the clock, so call and we’ll tell you honestly how soon we can be there. Call (888) 300-3906.
FAQs – Driveway Gate
How much does a driveway gate cost in Spring Valley?
A new driveway gate in Spring Valley typically runs $2,400 to $7,500 installed, depending on material and whether it swings or slides. Repairs run $180 to $650 for most issues. Call (888) 300-3906 for an exact quote, and estimates are free.
Can a sagging driveway gate be fixed without replacing it?
Usually, yes. A sag is almost always a hinge-post or footing problem, and resetting or reinforcing the post plus adjusting the hinge brings the gate back to square. We repair first because most sagging gates don’t need to be replaced. Call us and we’ll take a look.
Do you weld gates on site?
Yes. We weld steel and wrought iron gates right in your driveway so the gate never leaves your property. That saves the hassle of hauling and lets us fit the repair to the exact gate. Call (888) 300-3906 to schedule.
Why won’t my driveway gate opener close the gate?
Most often it’s a safety sensor knocked out of alignment or a gate that’s binding, which trips the operator’s safety reverse. Less often it’s a gear or control-board failure. Either way it’s diagnosable in one visit. Call and we’ll sort it out.
Do you offer a warranty on driveway gate work?
Every job carries the 90-Day Done Right Promise in writing. If it isn’t right, one call brings us back. No hedging, no fine print. Call (888) 300-3906 with any questions before or after the work.
If your driveway gate is sagging, stuck, or ready to be built, we’re the neighbor down the road who fixes gates for a living and puts the promise in writing. The name is on the shop and the shop is right here. For the wider range of options, see Gate Installation in Spring Valley, then call (888) 300-3906 for a free estimate. A live person answers, any hour.
Written by the team at Gatewood Fence & Gate Spring Valley, serving Spring Valley.